If you only need a left hand brake, we definitely have what you need. The Dexter Electric Trailer Brake Assembly # 23-26 will be just the left side (driver side) brake that will come with the # 23-26-27 Dexter 10 inch 3,500 pound brake kit. This will also include the mounting hardware so no other parts will be needed. view full answer...
Thanks for the photos!
Yes, the MB Sturgis Propane Pigtail w/ Back Check # 100575-12-MBS has the connections needed for both the regulator and the propane tank on your 2021 Grand Design Imagine 22MLE travel trailer.
If you wanted to get a pigtail longer than 12" (to ensure you aren't placing pressure on that joint) then I recommend checking out part # 100575-20-MBS which is the same thing just with a 20" length instead of a 12" length. view full answer...
From what I have found, the GVWR of your 2020 Grand Design Imagine XLS 22RBE is 6,995 lbs. Based on that information, you more than likely have 3,500 lb axles. The most common grease seal for a 3,500 lb axle is the # 58846 with a 1.719" inner diameter and 2.565" outer diameter. For a pair you would need the # RG06-050.
This is strictly based on your typical 3,500 lb axle. Ultimately there is no way to be sure without identifying the axle or the part number on the grease seal. If you are... view full answer...
I have some measurements for you which will allow you to verify if the Replacement Amber Lens # A44AB will fit your 2023 Grand Design Imagine XLS 17MKE. This lens is 4" long by 1-1/2" tall, see image below. Unfortunately, only Grand Design would be able to verify their part number 420713 is the same as the Optronics # A44AB since they create their own part number rather than using the manufacturer part numbers. view full answer...
The Replacement Black Top with Glass Cover # FR46NR is the correct part for your Furrion Range F1S17LO2A-BL. I confirmed this information with Furrion as they have several different models which are able to use many of the same parts. The top assembly is currently the only way Furrion offers the glass top. You may be able to have some glass made at a local glass shop to replace yours but as this is a tempered specialty glass they may not be able to make it for you. view full answer...
We do carry a few 15" x 6" wheels that are very similar to the Ocelot, but I am sorry to say that we do not carry the exact wheel you are looking for. I have listed a few similar Lionshead wheels below if you are interested.
Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Glossy Black # LH49FR
Aluminum Lynx Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Silver # LHSL311
Aluminum Liger Trailer Wheel - 15" x 6" Rim - 6 on 5-1/2 - Gunmetal Gray # LH37FR view full answer...
Since your axles are round it's actually best to measure with a set of calipers # PTW80157 instead of a tape measure, as you have to kind of eyeball and guess what the actual measurement is. Based on the picture you provided I can see you're under 3" so you would have a 2-3/8" axle unless you had some homemade axle, but I'm assuming with the age of the trailer that you're the original owner from the factory so that wouldn't be the case.
For 2-3/8" axles you'll need the CE Smith U-Bolt... view full answer...
Replacement Pitch Arm Assembly for Solera XL 63" Flat Awning Support Arm - Black # LC67VR is 63 inches as stated. That is the total length of the assembly. The parts department at Lippert who makes Solera couldn't give me the individual dimensions of the parts that are bolted together, so you will need to measure your assembly in the same way with the parts combined at straight length to determine compatibility. view full answer...
From what I have found, you need to following for your 3,000 lb Dexter axle:
Bearings- # L44649 outer bearing and # LM67048 inner bearing
Races- # L44610 outer race and # LM67010 inner race
Grease Seal- # 58846
I have attached a helpful video along with an article on replacing bearings and seals for your reference. view full answer...